厦门圣企机电设备有限公司
辅助触头:与断路器主电路分、合机构机械上连动的触头,主要用于断路器分、合状态的显示,接在断路器的
控制电路中通过断路器的分合,对其相关
电器实施控制或联锁。例如向信号灯、继电器等输出信号。塑壳断路
器壳架等级额定电流100A为单断点转换触头,225A及以上为桥式触头结构,约定发热电流为3A壳架等级额定
电流400A及以上可装两常开、两常闭,约定发热电流为6A。操作能次数与断路器的操作能总次数相同
触头:用于断路器事故的触头,且此触头只有当断路器脱扣分断后才动作,主要用于断路器的负载出
现过载短路或欠电压等故障时而自由脱扣,触头从原来的常开位置转换成闭合位置,接通辅助线路中的指
示灯或电铃、蜂鸣器等,显示或提酲断路器的故障脱扣状态。由于断路器发生因负载故障而自由脱扣的机率不
太多,因而触头的寿命是断路器寿命的1/10。触头的工作电流一般不会1A
分励脱扣器:分励脱扣器是一种用电压源激励的脱扣器,它的电压与主电路电压无关。分励脱扣器是一种远距
离操纵分闸的附件。当电源电压等于额定控制电源电压的70%-110%之间的任一电压时,就能可靠的分断断
路器。分励脱扣器是短时工作制,线圈通电时间一般不能15,否则线就会被烧毁。塑壳断路器为防止线圈烧
毁,在分励脱扣线圈串联一个微动开关,当分励脱扣器通过衔铁吸合,微动开关从常闭状态转换成常开,由于
分励脱扣器电源的控制线路被切断,即使人为的按住按钮,分励线圈始终不会再通电这就避免了线圈燒损情况
的产生。当断路器再扣合闸后,微动开关重新处于常闭位置
欠电压脱扣器:欠电压脱扣器是在它的端电压降至某一规定范围时,使断路器有延时或无延时断开的一种脱扣
器,当电源电压下降(甚至緩慢下降)到额定工作电压的70%至35%范围内,欠电压脱扣器应运作,欠
扣器
在电源电压等于脱扣器额定工作电压的35%时,欠电压脱扣器应能防止断路器闭合;电源电压等于或大于85%欠
电压脱扣器的额定工作电压时,在热态条件下,应能保证断路器可靠闭合。因此,当受保护电路中电源电压发
生一定的电压降时,能自动断开断路器切断电源,使该断路器以下的负载电器或电气设备免受欠电压的损坏
使用时,欠电压脱扣器线圈接在断路器电源侧,欠电压脱扣器通电后,断路器才能合闸
为满足轨道应用的需求条件,GE为您提供了完整系列的接触器、电动机保护开关和小型线路断路器。所有这
些元件都含特殊树脂,符合未来的prEN455452标准的要求。已获得多项认证例如U和csA等),可以在范围内广
泛运用。GE模块IC693PWR328美观大方GE模块IC693PWR328美观大方GE模块IC693PWR328美观大方
IC200MDL741CA
OUT 24VDC 机 .5A ESCP 16PT CONF COAT
IC200MDL741LT
OUTPUT 24VDC 机 LOGIC 0.5A PER PT (1 GROUP OF 16) W/ESCP 16PT (LT)
IC200MDL742
Output 24VDC 机 LOGIC 0.5 amp per point(2 group of 16) with ESCP 32 points
IC200MDL742LT
OUTPUT 24VDC 机 LOGIC 0.5A PER PT (2 GROUPS OF 16) W/ESCP 32PT (LT)
IC200MDL743
Output 5/12/24VDC NEG LOGIC 0.5A per point (1 group of 16) 16 points
IC200MDL743LT
OUTPUT 5/12/24VDC NEG LOGIC 0.5A PER PT (1 GROUP OF 16) 16PT (LT)
IC200MDL744
Output 5/12/24VDC NEG LOGIC 0.5A per point (2 groups fo 16) 32 points
IC200MDL744LT
OUTPUT 5/12/24VDC NEG LOGIC 0.5A PER PT (2 GROUPS OF 16) 32PT (LT)
IC200MDL750
Output 12/24VDC 机 LOGIC 0.5A per point (2 groups of 16) 32 points
IC200MDL750CA
Co
nformal Coated Output 12/24VDC 机 LOGIC 0.5A per point (2 groups of 16) 32 points
IC200MDL750LT
OUTPUT 12/24VDC 机 LOGIC 0.5A PER PT (2 GROUPS OF 16) 32PT (LT)
IC200MDL930
Output relay 2.0 amps per point isolated form A, 8 points
IC200MDL930CA
OUT RELAY 2A ISO FORM A 8PT conf coat
IC200MDL930LT
OUTPUT RELAY 2.0A PER PT ISOLATED FORM A 8PT (LT)
IC200MDL940
Output relay 2.0 amps per point isolated form A, 16 points
IC200MDL940CA
OUTPUT RELAY 2A ISO FORM A 16PT MODULE Co
nFORMAL COATED
IC200MDL940LT
OUTPUT RELAY 2.0A PER PT ISOLATED FORM A 16PT (LT)
IC200NAL110
10 point PLC, (6) 12VDC in, (4) Relay Out, (1) Analog Input (0-10VDC, 8 bit), 12VDC Power Supply
IC200NAL211
10 point PLC, (6) 24VDC In, (4) Relay Out, (1) Analog Input (0-10VDC, 8 bit), 24VDC Power Supply
IC200NAL211-24
Qty 24, 10 point PLC, (6) 24VDC in, (4) Relay Out, (1) Analog Input (0 -10VDC, 8 bit), 24VDC Power Supply
IC200NDD010
10 point PLC, (6) 12VDC In, (4) 12VDC Out, 12VDC Power Supply
IC200NDD101
10 point PLC, (6) 24VDC In, (4) 24VDC Out, 24VDC Power Supply
IC200NDR001
10 point PLC,(6) 24VDC In, (4) Relay Out, 24VDC Power Supply
IC200NDR001-24
Qty 24, 10 point PLC, (6) 24VDC In, (4) Relay Out, 24VDC Power Supply
IC200NDR010
10 point PLC, (6) 12VDC In, (4) Relay Out, 12VDC Power Supply
IC200PBI001
Remote I/O Profibus DP network interface unit
IC200PBI001CA
Remote I/O Profibus DP network interface unit co
nformal coated.
IC200PKG001
PLC starter kit CPU001
IC200PKG010
VersaMax Modular PLC starter kit. Kit includes CPUE05.
IC200PKG101
I/O starter kits, Genius NIU
IC200PKG102
I/O starter kit Profibus-DP NIU
IC200PKG103
I/O starter kit DeviceNet NIU
IC200PKG104
VersaMax Ethernet NIU starter kit with I/O.
IC200PNS001
PROFINET Scanner (PNS) module interfaces a remote node of VersaMax modules to a PROFINET IO Controller. Two 10/100 Mbps copper interfaces. Requires Proficy Machine Edition 7.0
IC200PNS001CA
Co
nformal Coated. PROFINET Scanner (PNS) module interfaces a remote node of VersaMax modules to a PROFINET IO Controller. Two 10/100 Mbps copper interfaces. Requires Proficy Machine Edition 7.0
IC200PNS002
PROFINET Scanner (PNS) module interfaces a remote node of VersaMax modules to a PROFINET IO Controller. Two 100Mbps Multi-Mode fiber (MMF) ports. Requires Proficy Machine Edition 7.0.
IC200PNS002CA
Co
nformal Coated. PROFINET Scanner (PNS) module interfaces a remote node of VersaMax modules to a PROFINET IO Controller. Two 100Mbps Multi-Mode fiber (MMF) ports. Requires Proficy Machine Edition 7.0.
